Rieju & GasGas Legacy Riders Club Forum

Rieju & GasGas Legacy Riders Club Forum (http://www.gasgasrider.org/forum/index.php)
-   Enduro Chassis & Body (http://www.gasgasrider.org/forum/forumdisplay.php?f=20)
-   -   99' EC200 Clutch M/C (http://www.gasgasrider.org/forum/showthread.php?t=20370)

12Bravo 10-16-2015 06:56 PM

99' EC200 Clutch M/C
 
Well, my M/C bit the bullet, or should I say a ROCK, today.

It is an AJP, I am having an issue finding a replacement that is in the States.

What can I use? Not wanting to break the bank on this, I just ordered my riding gear, so funds are tight.

Thanks

Zman 10-16-2015 06:59 PM

http://www.ebay.com/itm/2004-GasGas-...FWBJQT&vxp=mtr

http://www.ebay.com/itm/GAS-GAS-03-4...pVnVXH&vxp=mtr

12Bravo 10-16-2015 07:06 PM

That was fast.......I haven't even pulled Ebay up yet.

I think I am going to just order that $70 one and be done with it.....But after shipping it will be $100.

Are there any new ones that will fit? Will a Brembo work? I have found some AJP, but it is on a trials site, will those fit my bike? It was $130 new, I can pay the extra $30 and have a new one. If not, I will just get a used one.

Thanks

12Bravo 10-16-2015 07:49 PM

http://www.oppracing.com/product_dis...voir-wlever50/

Anyone know if this will work on my bike?

I got my M/C front brake from them, good company with fast shipping.

12Bravo 10-16-2015 09:44 PM

http://www.clake.com.au/product/one-light-clutch/

Wish I had the coin for this!

Half tempted to sell some of these extra parts I have to pay for the repairs. Waiting till mid-November to ride again doesn't sound fun at all!

I'm hooked I have the bug!

12Bravo 10-23-2015 04:49 PM

The good, I have the M/C installed.

The Bad it drags, when bike is running I can hold the clutch in and bike doesn't lunge. However with bike off and in first gear, clutch pulled in bike won't roll. It drags the tire or rolls very hard with a skid the roll a bit the skid then roll a bit again.


Does anyone know where I can get the M/C dust cover? The little rubber piece the covers the plunger from getting dirt in there. Mine is missing, I didn't notice when I ordered the replacement.

Thanks

David Podyuchenko 04-22-2024 12:20 PM

Can anyone help me? I've been searching for a while now... I have a 97 gasgas ec250 and my clutch slave main bolt connection where the banjo bolt screws in stripped. The slave thread stripped, banjo bolt is good. Any advice?

Anders 04-23-2024 02:11 PM

Quote:

Originally Posted by David Podyuchenko (Post 203023)
Can anyone help me? I've been searching for a while now... I have a 97 gasgas ec250 and my clutch slave main bolt connection where the banjo bolt screws in stripped. The slave thread stripped, banjo bolt is good. Any advice?

Helicoil?

Sent fra min YAL-L21 via Tapatalk

farmerj 04-28-2024 07:53 PM

Loctite Form-a-Thread might be worth trying (I haven't).

Jeff


https://www.napaonline.com/en/p/NCB28654


All times are GMT -5. The time now is 03:04 AM.

Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright 2009 - GasGasRider.org