|
Enduro Chassis & Body Enduro Frame, Plastic, Brakes, Bars, Controls, wheels, tires, sprockets & gearing. |
|
Thread Tools | Display Modes |
#1
|
||||
|
||||
99' EC200 Clutch M/C
Well, my M/C bit the bullet, or should I say a ROCK, today.
It is an AJP, I am having an issue finding a replacement that is in the States. What can I use? Not wanting to break the bank on this, I just ordered my riding gear, so funds are tight. Thanks
__________________
"There is no room in life for Regret, it's a useless feeling that leads to a negative attitude" I would rather call it the "Stupid Tax"! |
#2
|
||||
|
||||
|
#3
|
||||
|
||||
Quote:
I think I am going to just order that $70 one and be done with it.....But after shipping it will be $100. Are there any new ones that will fit? Will a Brembo work? I have found some AJP, but it is on a trials site, will those fit my bike? It was $130 new, I can pay the extra $30 and have a new one. If not, I will just get a used one. Thanks
__________________
"There is no room in life for Regret, it's a useless feeling that leads to a negative attitude" I would rather call it the "Stupid Tax"! |
#4
|
||||
|
||||
http://www.oppracing.com/product_dis...voir-wlever50/
Anyone know if this will work on my bike? I got my M/C front brake from them, good company with fast shipping.
__________________
"There is no room in life for Regret, it's a useless feeling that leads to a negative attitude" I would rather call it the "Stupid Tax"! |
#5
|
||||
|
||||
http://www.clake.com.au/product/one-light-clutch/
Wish I had the coin for this! Half tempted to sell some of these extra parts I have to pay for the repairs. Waiting till mid-November to ride again doesn't sound fun at all! I'm hooked I have the bug!
__________________
"There is no room in life for Regret, it's a useless feeling that leads to a negative attitude" I would rather call it the "Stupid Tax"! |
#6
|
||||
|
||||
The good, I have the M/C installed.
The Bad it drags, when bike is running I can hold the clutch in and bike doesn't lunge. However with bike off and in first gear, clutch pulled in bike won't roll. It drags the tire or rolls very hard with a skid the roll a bit the skid then roll a bit again. Does anyone know where I can get the M/C dust cover? The little rubber piece the covers the plunger from getting dirt in there. Mine is missing, I didn't notice when I ordered the replacement. Thanks
__________________
"There is no room in life for Regret, it's a useless feeling that leads to a negative attitude" I would rather call it the "Stupid Tax"! |
#7
|
|||
|
|||
Can anyone help me? I've been searching for a while now... I have a 97 gasgas ec250 and my clutch slave main bolt connection where the banjo bolt screws in stripped. The slave thread stripped, banjo bolt is good. Any advice?
|
#8
|
||||
|
||||
Quote:
Sent fra min YAL-L21 via Tapatalk
__________________
Anders "So you know, that you're over the hill when your mind makes a promise that your body can't fill" (Little Feat: Old Folks Boogie) 2015 EC200 Racing: TE bars, Rekluse Core Exp 3.0, 38mm Lectron & Ohlins S3 steering damper 2006 EC200: 2011 plastics, Rekluse Z-Start, revalved KYB forks & Scotts steering damper 1998 Bimota Supermono 1986 Duc Mille S2 1975 Guzzi sidecar hack 1961 Morini Corsaro 125 etc |
#9
|
||||
|
||||
Loctite Form-a-Thread might be worth trying (I haven't).
Jeff https://www.napaonline.com/en/p/NCB28654
__________________
'18 GG XC 300 '05 GG DE 300 '01 GG txt 321 |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Brake and Clutch lever crossover for 99 EC200 | Jgracey | Enduro Chassis & Body | 0 | 04-12-2015 09:26 AM |
Clutch Cover Oil Leak - 2001 EC200 | mlyle11 | Enduro Engine - 2 stroke | 2 | 06-03-2012 04:01 PM |
EC200 Clutch - or lack of | Muzungu | Enduro Engine - 2 stroke | 28 | 08-08-2011 08:15 AM |
03 EC200 clutch stuck after long sit | lankydoug | Enduro Engine - 2 stroke | 4 | 03-07-2011 10:47 AM |