|
Enduro Suspension Tuning & maintenance of Enduro forks, shocks, etc |
|
Thread Tools | Display Modes |
#1
|
||||
|
||||
baseline ohlins setting
i am 65kg were is a good place to start for a baseline setting??
i currently have hs=2 turns out ls=15 turns out rebound=30 turns out sag 110mm it still feels harsh sometimes and isnot sticking to the ground/tracking aswell as id like. im sure i dont have the best setting for my weight and am not a suspention tuner so dont know were to start thanks
__________________
06 EC250 |
#2
|
||||
|
||||
Stuff like this is pretty tough to do a virtual diagnosis on. But you might be a little light for that spring , provided that its the stocker that came on the bike.If its harsh and not staying planted I would try adding MORE comp and less rebound damping. Remember to do only one thing at a time.Good luck.
|
#3
|
||||
|
||||
Where is the shock harsh? Small trail junk, mid-size whoops, etc......
Do you bottom the shock? I have had good luck with the following I find a choppy section of trail on a hill. I adjust the shock full soft on compression and rebound. I ride the section of trail concentrating on the shock. I increase the compression 4 clicks stiffer and ride the hill. I repeat this until I notice the packing effect of the rebound being to slow. I back up 4 clicks and then start adjusting the HS compression. I keep adding 1/4 turn of compression until i notice the shock performance dropping. I back off 1/2 turn. The low speed compression requires big bumps to set properly. I pound through whoops, hit G-outs and such and figure out this setting. It's an easy adjustment on the trail, so I tend to adjust to the trails I'm riding. Big desert whoops require more low speed compression than my local riding areas. Anyway, once your in the ballpark, it fun to make small tweaks and see what happens. I softened my low speed compression on Sunday as the front end was biting too hard in the transition from hard pack to loam. Hopefully you lean the feel of the adjustments and can make educated guesses as to what to do in the future.
__________________
Mike Baxter 2005 GasGas EC300 (Ohlins front and rear) 2007 Yamaha FZ1 2003 Pampera 280(hers) |
#4
|
||||
|
||||
it feels like its a bit harsh in the smaller stuff and in rocks i have just changed oil in my forks so i think thats why the shock is also behaving differently as forks seem a bit firmer. what do you have your rebound set at?? and the forks seem to bounce off rocks more now i have 110mm air gap in forks and i might try 120mm thankyou for ya help
__________________
06 EC250 |
#5
|
||||
|
||||
Are you running the stock springs?
They are likely to stiff for your weight. Browse through the Suspensions section, there are a lot of threads discussing spring ratios. |
#6
|
||||
|
||||
stock springs
__________________
06 EC250 |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
FAQ; Suspension baseline settings | LTRace | Enduro Suspension | 39 | 04-06-2019 06:51 AM |
Help with air screw setting on RB-carb | joey11 | Enduro Intake/Carburetion - 2 stroke | 7 | 02-17-2009 07:09 AM |
2005 baseline settings | stay_upright | Enduro Suspension | 0 | 01-26-2009 08:37 AM |
Setting up my EC300R 09 | Keg | General Discussions & Announcements | 4 | 09-27-2008 07:42 AM |
EC300 Baseline settings | Magellan | Enduro Suspension | 7 | 08-26-2006 06:30 AM |