|
Enduro Electrical & Wiring Lighting, Ignition, Wiring, Plugs, etc. |
|
Thread Tools | Display Modes |
#1
|
||||
|
||||
off sticky ignition questions
number one i posted in the sticky but didnt get any response...
my new(98) 250 has a 2k2 in it now it exits the case on the front side with a plastic cover, but it came with another magnesium cover that has another coil in it, which also exits in the front, but from the cover itself, not the case, and it wil actually bolt on over what already there,although its too far away to do anything.. what is this? question number 2 was how do i post pics but i figured it out lol
__________________
Le Crutan 98 ec250 sixdays, doma, eline pipe guard, zokes shivers from a cr250,fredette racing chain slider, protaper withbarkbusters (SOLD) FOR THE SECOND TIME 07 EC300 polisport headlight, acerbis taillight ltr pv cover and case saver,trailtech endurance,120z fww, g2 throttle,xr chain puck: Last edited by mountain thumper; 07-13-2009 at 01:48 PM. Reason: der derder |
#2
|
||||
|
||||
I should wait till the smart guys around here give you the "right" answer.
But, I'll give it a stab and hope not to look like a chump. The frist picture looks like the newer 2K2 ignition on the 2000 and up bikes. The lower picture looks like the older Ducati type ignition from the 96-99 EC models. If the bike in the first picture is supposed to be a 1998. It looks to me like it does not have the counter balancer installed like it should. Ok, I'll sit back and see if my WAG was even close. Jeff So. Cal. |
#3
|
||||
|
||||
You nailed it buddy!
|
#4
|
||||
|
||||
Thanks Mr. Bear. I guess I kind of cheated on the test........
I have the same set up on my 98 as the bottom picture of the OP. The outer portion is the high output lighting coil. I can't remember taking off the left side stator cover to see how everything is hooked up and mounted on that 98. I did the 2K2 to 2K3 with the floating gound mod on my 02. But since Smackover racing installed the large Ducati unit on my 98. I have not looked inside to see how it works.....I smell "weekend project" As I plan to add a battery and a Rectifier/Regulator to the 98. I'll need to learn the "doos-n-don't" with that system too. Im think'n there is more to it for the original poster than just adding the MAG side cover and get instant power. Where IS Mr. Jim Cook when you need him? He'll have the answers for you. And I'll bet Mr. Marolda would know the insides of this unit just as well. Jeff So. Cal. |
#5
|
||||
|
||||
Jeff. Nice looking bike. Where in the world did you score those 01 blk rad shrouds?
|
#6
|
||||
|
||||
Never mind that, how do you score a plate for that in Cali?
|
#7
|
|||
|
|||
Seriously, that's a real trick!
__________________
2003 EC250 w/ Ohlins pkg Sometimes you eat the bear, sometimes the bear eats you. |
#8
|
||||
|
||||
Back to the ignition. Thats the old Ducati energia system. There should be a an additional rotor magnet, like a spin on flywheel weight, that goes on the small 2K-2 flywheel and engages the coils in the cover.
|
#9
|
||||
|
||||
Widebear: Where in the world did you score those 01 blk rad shrouds?
"Luck and a lot of watching the internet for GasGas items for sale." I have a spare NOS set sitting in a box. These were new several years ago, I think I got them from Jim Cook and added the graphics from GoFasters. As for the plate. The bike was built by Steve @ MotoWest. Bought by a friend who took it to Colorado and got a plate for it there. I bought it from friend in 2002 or so and took the Co. plate and the bike to Ca. DMV. It flew right past the Vehicle inspection and they issued a plate no questions asked. BTW, the bike is a hoot to ride in the local mountain canyons. Here is a picture from near the famous "Rock Store" in Malibu. |
#10
|
||||
|
||||
Quote:
does anyone know where to get the extra bit to run this coil? gofasters doesnt have anything this old that i can see! could i just weld on an extension with magnets to the fw thats on it already and use that coil completely seperate from the ignition? a pic of the magnets would help a lot too, its got 14 coils, grouped into 4 sets, 2 long sets, 2 short sets....
__________________
Le Crutan 98 ec250 sixdays, doma, eline pipe guard, zokes shivers from a cr250,fredette racing chain slider, protaper withbarkbusters (SOLD) FOR THE SECOND TIME 07 EC300 polisport headlight, acerbis taillight ltr pv cover and case saver,trailtech endurance,120z fww, g2 throttle,xr chain puck: Last edited by mountain thumper; 07-14-2009 at 01:42 PM. Reason: additional question not worth another post! |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Request for a sticky.... | stay_upright | Enduro Intake/Carburetion - 2 stroke | 0 | 07-08-2008 07:10 AM |
Sticker sticky stuff | stay_upright | Enduro Chassis & Body | 0 | 03-04-2008 02:13 AM |
Sticky power valve?? | moff747 | Enduro Engine - 2 stroke | 9 | 12-22-2007 07:59 AM |
Fun times with a sticky carb!?! | JoshP | Enduro Intake/Carburetion - 2 stroke | 8 | 01-28-2007 03:41 PM |
04 300EC Ignition changed to DE Ignition | Trail Blazer | Enduro Engine - 2 stroke | 0 | 01-08-2007 01:48 AM |